Products C295
95-92053-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The ARTCU Troubleshooting Box allows the operator to analyze the inputs and outputs of the ARTCU (Autotrim and Rudder Travel Control Unit).
95-92052-0003
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The Protractor is a protractile equipment to measure the angle made up by two planes, such as the angle made up by the aircraft with its respective flight control surfaces.
95-92056-0005
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The DC Capacitace Measurement Test Set allows the operator to check the correct operation of the fuel level probes located in the tanks of the CN-235 and C295 aircraft.
95-92084-0005
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The Manual Control, Ramp & Ventral Door equipment allows the operator to manually control the Ramp and Ventral Door of the CN-235 and C295 aircraft.
95-92118-0003
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The Flap Control Test Box is equipment that facilitates the operator's access to the signals between the Electronic Control Unit (CE3 Connector) and the Flaps system.
95-93031-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The Quadrant Control Test Box allows the operator to test the operation of the C-295 aircraft's Quadrant Control, both when mounted on the aircraft and outside the aircraft.
95-92462-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The MLG Door Retraction Actuator Rigging Tool is a GSE used to measure the distance between Earth-End and Rod-End of the MLG doors actuator.
95-92463-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The MLG Inner Door Support is a STE used to support the Inner Main Landing Gear (MLG) door in order to keep it opened during rigging of the landing gear subsystems.
95-92464-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The MLG Roller Uplock Rigging Tool is a STE used to rig the associated roller/hook elements to accomplish an acceptable interface of the doors and mechanism in close position.
95-92470-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The MLG Door Kynematics Rigging Tool is a STE used to measure the overcenter of the Outer and Inner MLG Doors.
95-92522-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The IOC-4110 SW Loading Harness consists in a harness to connect an ARIN 615 Data Loader to the Input and Output Concentrator (IOC) to perform the load of the Input and Output Table (IOT-4110) software.
95-92523-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The ADC-3010 SW Loading Harness is a GSE used to connect an ARINC 615 Data Loader to the Air Data Computer to perform the load of the Aircraft Configuration Table ACT-3010 Software.
95-92527-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The JIG Extension Cable is a GSE used to reload the Aircraft Personality Module (APM), which belongs to IRS system, model LASEREF VI of C-295 aircraft.
35-92288-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The Doors Micro Switches Test Box is used to test all door micro-switches on the CN-235 and C-295 aircraft
95-92461-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The APM Switch is a STE used to adjust and align the EFVS (Enhanced Flight Vision System).
35-92129-0007
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The Micro Switches Test Box is a GSE used to test the Landing Gear Micro Switches and the Panel Control System of the Aircrafts CN-235, C-295.
95-92082-0005
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The Potentiometer Test Box is a GSE used to perform the tests and adjustment of the potentiometers signal of the Flap System (FLAP 1, FLAP 2) of both C-295 and CN-235 aircrafts.
95-92019-0001
35-92720-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The GSE “Extinguisher Discharge Cartridge Simulator” is used to simulate the real cartridges of the Engine Fire Extinguishing System of the C-295 and CN-235 aircrafts.
35-92720-0001
EQUIPMENT MANUFACTURED EXCLUSIVELY FOR AIRBUS D&S
The HE7 harness is used to allow voltage monitoring of the Primary Outflow Valve during the pressurization control system function test
